Paul

Just a quick update, it does need the ECU, plugged in and the pump primes. Thanks Paul

All Done thanks Sonny

bosch mate

Red and black, do they go to the starter and then to the alernator? or a single red to the alternator? plus a couple of small wires? Paul

Can anyone tell me how the starter motor / alternator cables are connected from the battery? Ta Paul

Had it fitted to my Clifford, never used it because always forgot to put it in safety mode before turning the engine off lol. These work well on automatic cars but manual are to much trouble. Not going back on after the rebuild.

Hi mate, have you got the diagram for the 90 onwards EFI wiring? Paul

one daft question i have no ecu connected would this affect it

full loom but left the original fuel pump wires from back seat to pump and joined under seat only 2 wires the one for the pump and the one for render unit, the earth connections seem ok and are still attached under seat base. Havent got starter or alternater wired but this should not affect it should it

Is there a fuse or relay in in the fuse box for this? Or is it just the yellow one under the dash (EFI)

yes mate 2nd click, but having probs with battery at moment so might be a case of not having enough volts to switch relay

thanks mick

No volts on fuel pump positive wire any ideas? Changed relay and thats ok. Paul

Hi all, when fitting new Gaz rears to a mk4 do you just leave the yellow supplied bump stop on or do you replace it with the Ford fitment?

Hi all what is the sensor / ? on top of the coil bracket on the EFI? What is it called and has anyone got a spare Paul

Last night we managed to bolt the head down and set up the timing. The head had a new Piper 285T2 Cam, Piper lifters, vernior pully and Piper Cam belt fitted before it was bolted down on the block. The head has also had a lot of work on it being ported and polished etc. The block had been fitted with steel con rods, forged pistons and flywheel lightened etc etc.

Haven’t updated this is ages mainly due to work, money etc and slight loss of interest but back on track. The new EFI loom has been installed, this was a task in it self has i didn’t want to cut and join any of the loom. So all the interior was ripped out to make way for it. I managed to pick up a mint loom thanks to Ant at Just Affords. The loom had never seen a alarm and even the original stereo connector was in place and it came from a Cab so all good. I have just finished putting 90% of the interior / dash / boot back in so its starting to look like a car again. The engine bay is also starting to fill up again, managed to get the reconditioned steering rack etc back in place and all the front suspension all back on. Decided to replace the 18 month old Konis with Gaz fully adjustable, new hubs have been purchased and powder coated and all other items related to the suspension have been re powder coated black I.E anti roll bar etc. New Powerflex poly bushes have also been added. I will get some pictures of the front suspension setup ASAP. We have also assembled the gearbox together with its new 4 Paddle AP racing clutch and bolted up with the block. New Vibratech engine mounts have been fitted. The block and gearbox, cradle etc was built up outside the car and then raised up into the car with the help of Andy, Eric and Andy (F40) and bolted into place with re zinced bolts and washers. The head in the picture was just resting on top of the block so it didn’t get kicked around to much.

I have a good RST Engine for sale, drop me a PM

Thanks Taz for your help mate, all sorted

Ok, changed my MFI loom to a EFI and all the plugs and sockets fit? Except i cannot find a home for the 2 pin connector from the electric antenna. The relay for it is mounted using a screw behind the clocks and the lead coming from the relay has a inline fuse to a 2 pin connector. Dis they change this on the EFI? Paul

I have some single piston cossie ones with sliders here, are they 2 or 4 wheel drive? Paul

Hi, do i need 2 or 4 wheel drive cossi brakes for the front? single or 4 pot? Paul

Can anyone tell me the differences between MFI and EFI relays, Noticed that on EFI the fuel pump relay is not pink, also i seem to have a 6 pin hella relay (poss flasher unit) that i have no efi wiring for? Paul

Can anyone tell me which order the 4 relays under the dash should live?

Will be sent out on Monday via recorded del. Paul